Home    News    Tool Box    About    Search   
article categories
Automotive
Computer
Electronics
Food and Cooking
Home Improvement
Household
Personal Finance
Pets and Animals
Pool and Spa
Recreation Vehicle - RV
article categories
How To Videos
SUBMIT ARTICLE Newsletter Signup
Newsletter Archive
DIY Links and Resources
Advertise Here

Lumber Liquidators

NorthernTool.com

Interstate Batteries.com

Once You Know, You Newegg

Tool King Service, Selection, Satisfaction

Repairing a Hole in a Sheetrocked Wall

By Mark Donovan

It is quite simple to repair a hole in a Sheetrocked wall, however there are minor differences in methods of repair depending on how large the hole is.

Small size holes (1/4” or smaller)

With small holes, simply apply a little joint compound or wall putty with a small putty knife or trowel. Let dry, then sand lightly and paint.

Medium size holes (Greater than ¼” in diameter and smaller than 2” in diameter)

First clean out the hole and surrounding area of any debris and loose sheetrock. Then apply a mesh tape, specifically manufactured for sheetrock applications, across the hole. Use your putty knife to ensure that it is applied evenly on the wall surface. Next apply a liberal amount of Joint Compound over the hole and mesh. Let this set for 1 to 2 days.

After the initial coat has been applied and has had time to fully dry, apply a second skim coat of Joint Compound over the area. However, this time spread the Joint Compound over an area that is 2-3 times the size of the original hole. Basically you want to flare out the area that you are repairing so that it will blend in nicely with the rest of the wall. Again let the area dry for a day.

Finally lightly sand the area and apply one last skim coat over the area. Again spreading the Joint Compound out a little further than the last application. Let the Joint Compound set up one more day, sand lightly and then paint.

Holes larger than 2 inches

With large holes, I recommend cutting out an area such that a new small piece of sheetrock can be applied to the 2”x4” studs. For example, I would consider putting in a new 16”x16” piece of sheetrock for a hole that is greater than 2” in diameter and less than 16” in diameter.

The best method to remove the piece of damage sheetrock is to use a Carpenters knife (razor blade) and score the area where you want to cut out. Repeatedly apply the knife until you have worked your way through the sheetrock. When complete, you should have about ½” to ¾” of the 2”x4” stud showing on each of the two exposed studs.

Note: Care should be taken to ensure no wires are cut behind the sheetrock when cutting out the damaged piece.

Next, cut a piece of new sheetrock to the size of the hole, and secure with sheetrock screws or ringed sheetrock nails.

Next, tape the cracks with the mesh tape material mentioned above. Then as described earlier, apply three skim coats of Joint Compound, with each successive coat getting flared out further. Make sure you wait for the Joint Compound to dry before applying the next coat. Perform a final light sand after the final coat has been applied and has had time to dry, and then paint.

About the Author:
me_donovan@comcast.net
http://www.homeadditionplus.com
http://www.homeaddition.blogspot.com

Over the past 20+ years Mr. Donovan has been involved with building homes and additions to homes. His projects have included: building a vacation home, building additions and garages on to existing homes, and finishing unfinished homes. Mr. Donovan's formal education and profession have been as an Electrical Engineer and Marketing Manager.

Article Source: http://EzineArticles.com/?expert=Mark_Donovan
http://EzineArticles.com/?Repairing-a-Hole-in-a-Sheetrocked-Wall&id=22950

  Did You Know...  
Lake Powell is the 2nd largest man-made lake in the United States.
Source: LakePowell.com

Fun fact# 44

    © DC Systems 2014    
home | news | Tool Box | contact
      Get Firefox!